Objet living hinges

Advanced Applications

Say yes to the most demanding opportunities

Quick turnaround. Low-volume customized parts. Complex components and geometries that are impossible to machine. With Stratasys technology and expertise, you can meet these manufacturing challenges and more.

Alternate Support Methods for Build Optimization

Overview

Optimizing performance becomes increasingly important as a project moves from prototype application to direct digital manufacturing (DDM). With larger production quantities, even a small decrease in material consumption and build time can have a large impact on production expense and throughput.

With a few minor adjustments to the default parameters for FDM supports, DDM applications can have times and material volumes cut in half. And since the methods are so simple to apply, it is just as easy to save time and money on the prototypes made for product development.

Method 1: Fast–Build Supports

To decrease both build time and the volume of support material, increase the distance between the support material rasters. The larger air gaps will decrease build times by up to 22 percent and decrease the volume of support material by up to 40 percent.

Default Style

Reduction: Fast-Build

Build Time (hours)

Material (in3)

Time (hours)

Material (in3)

Sample_1

31.42

68.78

4.72

18.89

Sample_2

58.27

136.51

5.61

16.46

Sample_3

8.95

6.61

0.17

0.74

Sample_4

42.57

53.83

2.42

6.86

Sample_5

21.13

61.06

0.28

1.21

Sample_6

33.15

89.82

7.30

30.42

Sample_7

5.77

5.82

0.32

1.65


1. Create Custom Group:

Select the SupportSparse template and save it as a new custom group named SupportFast.

Change the Air Gap between adjacent rasters to 0.79 inch (20.0 mm). Also, adjust the Start Angle to make it perpendicular to that used in the SupportSparse group. For example, with ABS-M30 and a T16 tip, the Start Angle would be set to 150 degrees. Next, set the Delta Angle to zero degrees and check the box for Align Rasters.

2. Apply Custom Group:

Apply the SupportFast group to any SupportSparse groups that are more than ten layers below the Support curves. Leave the ten–layer boundary of SupportSparse curves unchanged.

The ten–layer region acts as a buffer zone that ensures that all faces of the model are properly supported. At the transition between SupportFast and SupportSparse, the raster will sag because of the larger air gap. This sag lessens with each subsequent layer. By the tenth layer, the sag is eliminated, which provides a fl at contour for the subsequent support material curves.

Method 2: Supports Made from Model Material

Another alternative to decrease build time is to substitute model material, such as ABS–M30, for the support material. Making both the model and support from a single material eliminates the lag when switching between materials. If combined with the Fast–Build supports method, build times can be reduced by as much as 40 percent.

This method is simple to implement. However, it is not applicable for every FDM part. To be effective, all supports on a given layer must be made from model material. Also, the geometry of the supports must be such that they are not captured by the part. Although the WaterWorks™ support zone allows the support to release from the part’s surface, removal will be diffi cult if the model or supports surround each another.

Default Style

Reduction: Fast-Build + Model Supports

Build Time (hours)

Time (hours)

Sample_1

31.42

6.05

Sample_2

58.27

5.70

Sample_3

8.95

3.12

Sample_4

42.57

3.75

Sample_5

21.13

2.33

Sample_6

33.15

10.03

Sample_7

5.77

2.09


1. Create Custom Group:

Select the SupportSparse template and save it as a new custom group named SupportModel. The only parameter to adjust is Toolpath Material. Set this option to “model”.

2. Combine with Fast–Build supports.

Optionally, SupportModel can be combined with the Fast-Build method described above. To use this option, add a custom group named SupportFastModel. Use all of the parameters for SupportFast but set the Toolpath Material to be “model.”

3. Apply Custom Group:

Both SupportModel and SupportFastModel are applied to any support material curves that are three or more layers from the SupportFace curves. This two–layer boundary of soluble support material allows the supports to separate from the part when submersed in the WaterWorks solution.

Stratasys Ltd. © 2015. All rights reserved. See stratasys.com/legal for trademark information.